Technical Forums» Technical / Performance» arp head studs
|
Majiga » CMF Member bundaberg Australia Member since:  Posts:  |
arp head studs |
Wed 09 Oct 2013 06:03:36 PM |
|
anyone had these made if so where? and is my only option mailing them studs to be copied? or is there another thicker stud of similar length i could re drill and tap to suit them?
any ideas would be appreciated. |
||
|
|
||
|
frank2 » CMF Member birmingham United Kingdom Member since: Posts: |
Re: arp head studs |
Wed 09 Oct 2013 06:26:23 PM |
|
they will just need a length measurement surely ? good luck finding some flanged nuts and a strong enough socket that will fit down that hole tho !
|
||
|
Majiga » CMF Member bundaberg Australia Member since: Posts: |
Re: arp head studs |
Wed 09 Oct 2013 10:04:00 PM |
|
hmm i guess not then back to the drawing board :( thx frank
|
||
|
frank2 » CMF Member birmingham United Kingdom Member since: Posts: |
Re: arp head studs |
Wed 09 Oct 2013 10:24:35 PM |
|
you would need these 12 sided nuts eh, and a 3/8 drive deep 12mm socket should just about stand 100nm of torque, but i think you would need to grind some off the flanges tho
|
||
|
Mickb » CMF Member Perth Australia Member since: Posts: |
Re: arp head studs |
Wed 09 Oct 2013 11:17:53 PM |
|
I have a set in mine, I can have a look tomorrow and see if I have the part numbers. The are off the shelf, not custom made. no grinding necessary for me.
|
||
|
SSUK » CMF Member London United Kingdom Member since: Posts: |
Re: arp head studs |
Thu 10 Oct 2013 12:22:43 AM |
|
Same here, been done a few times now. No access to the car right now though.
|
||
|
Majiga » CMF Member bundaberg Australia Member since: Posts: |
Re: arp head studs |
Thu 10 Oct 2013 07:28:55 AM |
|
thx guys :) been a headache
|
||
|
Mickb » CMF Member Perth Australia Member since: Posts: |
Re: arp head studs |
Thu 10 Oct 2013 08:21:16 AM |
|
No luck mate. Give arp a call?
|
||
|
Majiga » CMF Member bundaberg Australia Member since: Posts: |
Re: arp head studs |
Thu 10 Oct 2013 10:20:19 AM |
|
no luck with arp so far. they reckon they got squat i see a whole bunch of micras online with them no one has a part number.
|
||
|
frank2 » CMF Member birmingham United Kingdom Member since: Posts: |
Re: arp head studs |
Thu 10 Oct 2013 05:42:44 PM |
|
when you find some :) bear in mind the pitch of the thread on the nut, and the (60deg) torque angle setting majiga
|
||
|
Majiga » CMF Member bundaberg Australia Member since: Posts: |
Re: arp head studs |
Thu 10 Oct 2013 06:12:26 PM |
|
yeah good point im leavin it to the engine builder to find but that could take another year.
|
||
|
turbo march-rolling shell » CMF Member brisbane Australia Member since: Posts: |
Re: arp head studs |
Sat 19 Oct 2013 09:54:46 PM |
|
...if you ask really nicely I'll give you the arp part number.
|
||
|
Majiga » CMF Member bundaberg Australia Member since: Posts: |
Re: arp head studs |
Sun 20 Oct 2013 12:34:40 AM |
|
tmrs may i have the part number please hehe if you have it would be awesome may even have strawberries on top lol
|
||
|
turbo march-rolling shell » CMF Member brisbane Australia Member since: Posts: |
Re: arp head studs |
Sun 20 Oct 2013 01:34:57 PM |
|
Lol arp part number is 151-4203
|
||
|
Majiga » CMF Member bundaberg Australia Member since: Posts: |
Re: arp head studs |
Mon 21 Oct 2013 08:26:52 AM |
|
tyvm tmrs much appreciated.
|
||
|
Pierce » CMF Member Logan Australia Member since: Posts: |
Re: arp head studs |
Sat 26 Oct 2013 10:30:22 AM |
|
Hey TMRS,
Just wondering if it matters that the parts search comes up with: Ford Escort Head Stud Kit Kit #: 151-4203 Jobber Price: $151.79 Are they a perfect match? |
||
|
Majiga » CMF Member bundaberg Australia Member since: Posts: |
Re: arp head studs |
Mon 18 Nov 2013 12:22:26 PM |
|
yeah mate fit them today to see. they will work a treat.
|
||
|
Pierce » CMF Member Logan Australia Member since: Posts: |
Re: arp head studs |
Tue 19 Nov 2013 06:26:10 AM |
|
great to hear :D
I'll buy a set today - I was holding off due to possible stuff around. |
||
|
Majiga » CMF Member bundaberg Australia Member since: Posts: |
Re: arp head studs |
Tue 19 Nov 2013 09:37:35 AM |
|
yeah the engine builder laughed and said wow a part i don't have to stuff around with.
|
||
|
Pierce » CMF Member Logan Australia Member since: Posts: |
Re: arp head studs |
Tue 19 Nov 2013 09:46:54 AM |
|
Great to hear :-)
Did you have springs n tappets made ? If so was there any reason because I'm not sure I need them though I could be swayed... |
||
|
plattsy » CMF Member melbourne Australia Member since: Posts: |
Re: arp head studs |
Tue 19 Nov 2013 11:39:07 AM |
|
anyone have part number for arp manifold studs? do they make them even????
|
||
|
Pierce » CMF Member Logan Australia Member since: Posts: |
Re: arp head studs |
Tue 19 Nov 2013 12:46:39 PM |
|
My exhaust and intake manifold have nuts over the bolts off the bloc. Surely loctite nuts are enough?
|
||
|
plattsy » CMF Member melbourne Australia Member since: Posts: |
Re: arp head studs |
Tue 19 Nov 2013 01:47:31 PM |
|
yea, but when i take the manifold off, those block studs are going to break. its a nissan. haha!
|
||
|
Pierce » CMF Member Logan Australia Member since: Posts: |
Re: arp head studs |
Tue 19 Nov 2013 02:28:03 PM |
|
Haha fair enough, considering that id replace them but mine are in new condition as they were weatherproofed well with a bit of anti rust and engine bay paint a while ago.
|
||
|
plattsy » CMF Member melbourne Australia Member since: Posts: |
Re: arp head studs |
Tue 19 Nov 2013 04:19:29 PM |
|
yea im just scouring ebay uk to find stuff....
|
||
|
Majiga » CMF Member bundaberg Australia Member since: Posts: |
Re: arp head studs |
Wed 20 Nov 2013 12:56:33 AM |
|
nah going with new stock spring no point makin it work harder than it has to and using stock cam thingo's too with jun titanium retainers
|
||
|
plattsy » CMF Member melbourne Australia Member since: Posts: |
Re: arp head studs |
Wed 20 Nov 2013 09:05:16 AM |
|
where do people find all these jap parts! jun reatainers, fancy flywheels etc. point me in the right direction guys!
|
||
|
kovert.k11 » CMF Member onjomama Australia Member since: Posts: |
Re: arp head studs |
Wed 20 Nov 2013 09:24:42 AM |
|
google does fantastic things these days.. searching cmf also helps...
|
||
|
plattsy » CMF Member melbourne Australia Member since: Posts: |
Re: arp head studs |
Wed 20 Nov 2013 11:49:09 AM |
|
the sarcasm is strong in this one..... haha! no worries man, will continue to google. just thought there may have been some miraculous site that had all k11 bits!
|
||
|
turbo march-rolling shell » CMF Member brisbane Australia Member since: Posts: |
Re: arp head studs |
Fri 22 Nov 2013 07:41:22 AM |
|
Pierce WROTE:
I wouldn't say hey go buy these they will work if they won't Mate.... Majiga WROTE: "nah going with new stock spring no point makin it work harder than it has to and using stock cam thingo's too with jun titanium retainers" Please tell me your not using stock cams and gears, there's so much midrange benefit to be had there it's not funny. Where you revving this thing to |
||
|
Majiga » CMF Member bundaberg Australia Member since: Posts: |
Re: arp head studs |
Fri 22 Nov 2013 11:16:06 AM |
|
nah using the group a 773 cams from matt humphries and struggling to find adjustable cam gears if you know where i can get a set would be awesome.
|
||
|
AB-NRML » CMF Member Perth Australia Member since: Posts: |
Re: arp head studs |
Fri 22 Nov 2013 03:00:26 PM |
|
Majiga WROTE: "nah using the group a 773 cams from matt humphries and struggling to find adjustable cam gears if you know where i can get a set would be awesome." ^+1^ |
||
|
Pierce » CMF Member Logan Australia Member since: Posts: |
Re: arp head studs |
Fri 22 Nov 2013 04:41:18 PM |
|
Majiga,
I just put my engine into PLR at northside QLD, they were pretty helpful, didn't try to swindle me or tell me i need this and that... I was talking to him about getting some adjustable cam gears as well. They said they'll look into it and get back to me. |
||
|
kovert.k11 » CMF Member onjomama Australia Member since: Posts: |
Re: arp head studs |
Fri 22 Nov 2013 05:32:12 PM |
|
http://www.mulholland-rp.com/eng.htm >>>> there you go girls - adjustable cam gears
|
||
|
Pierce » CMF Member Logan Australia Member since: Posts: |
Re: arp head studs |
Fri 22 Nov 2013 08:05:48 PM |
|
Love ya work Kovert :D
I'll contact em and see where it leads. Cheers. EDIT: Using importmonster.com.au to organise a quote as I have $40 sittin on my account. |
||
|
frank2 » CMF Member birmingham United Kingdom Member since: Posts: |
Re: arp head studs |
Fri 22 Nov 2013 09:15:38 PM |
|
what size socket head were the arp nuts incidentally majiga ?
|
||
|
Majiga » CMF Member bundaberg Australia Member since: Posts: |
Re: arp head studs |
Fri 22 Nov 2013 11:34:27 PM |
|
not sure frank they were small 12mm ish
|
||